4.Cutter Recommendations

     Fabric Hot Stamp Flex use by conventional cutting plotters such as : Roland GS-24, Mimaki CG-60SR,Graphtec CE6000 etc. and desk cutting plotter: such as Panda Mini cutter, Silhouette CAMEO, GCC i-Craft, Circut

5.Cutting plotter setting

    You should always adjust the knife pressure, cutting speed according to your blade ages and the Complicated or size of text.

Note: The above technical data and recommendations are based trials, but our customer’s operating environment, non-control, we do not guarantee their applicability, Before use, Please to first full test.

6.Home Iron-On transferring

Step 1:
■ Prepare a stable, heat-resistant surface suitable for ironing on.
■ Preheat the iron to the < wool> setting, recommended ironing temperature 165°C.

Step 2:
■ Briefly iron the fabric to ensure that it is completely smooth, then place the Fabric Hot Stamp Flex  onto it with the cutted image facing downwards.
■ Do not use the steam function.
■ Make sure that the heat is evenly transferred over the entire area.
■ Iron the Fabric Hot Stamp Flex , applying as much pressure as possible.
■ When moving the iron, less pressure should be given.
■ Don’t forget the corners and edges.

■ Continue ironing until you have completely traced the sides of the image. This entire process should take about 60-70 seconds for an 8”x 10” image surface. Follow-up by ironing the whole image quickly, heating all of the abric Hot Stamp Flex again for approximately 10-13 seconds.
■ Peel the back film starting at the corner when completely cold.

Step 3:
■ Place the Hot Stamp Foil onto it with the coated facing downwards. and then place a grease proof paper on it 
■ Iron the grease proof paper, applying as much pressure as possible.
■ When moving the iron, less pressure should be given.
■ Don’t forget the corners and edges.
■ Continue ironing until you have completely traced the sides of the coated. This entire process should take about 25-35 seconds for an 8”x 10” image surface. Follow-up by ironing the whole  coated quickly, heating all of the grease proof paper again for approximately 10-15 seconds.
■ Peel the Hot Stamp Foil starting at the corner when completely cold.

7.Heat press transferring

Step 1:
■ Setting heat press machine 165°C for 15~25 seconds using moderate pressure. the press should snap closed firmly.
■ Briefly press the fabric 165°C for 5 seconds to ensure that it is completely smooth.
Step2:
■ Place the Fabric Hot Stamp Flex onto it with the cutted image facing downwards.
■ Press machine 165°C for 5~10 seconds.
■ Peel the back film when completely cold starting at the corner.
Step3:
■ Place the Hot Stamp Foil onto it with the coated image facing downwards.
■ Press machine 165°C for 5~10 seconds.
■ Peel theHot Stamp Foil when completely cold starting at the corner.

8.Washing Instructions:

Wash inside out in COLD WATER. DO NOT USE BLEACH. Place into the dryer or do hang to dry immediately. Please do not stretch the image transferred or the T-shirt as this may cause cracking to occur, If cracking or wrinkling does occur, please place a sheet of greasy proof paper over the transfer and heat press or iron for a few seconds making sure to press firmly over the entire transfer again. Please remember to not iron directly on the image surface.

9.Finishing Recommendations

Material Handling & Storage: conditions of 35-65% Relative Humidity and at a temperature of 10-30°C.
Storage of open packages: When an open packages of media is not being used remove the roll or sheets from the printer cover the roll or sheets with a plastic bag to protect it from contaminants, if you are storing it on end, use an end plug and tape down the edge to prevent damage to the edge of the roll do not lay sharp or heavy objects on unprotected rolls and do not stack them.